主營產品：閥門、氣動元件、儀器儀表、電子元器件
產品[

CIT-03-04-50，YUKEN葉片泵參數[產品打印頁面]

]資料
如果您對該產品感興趣的話,可以
產品名稱: CIT-03-04-50，YUKEN葉片泵參數
產品型號: CIT-03-04-50
產品展商: YUKEN
簡單介紹
CIT-03-04-50，YUKEN葉片泵參數 The pollution control of hydraulic oil, and maintain the pollution level within the NAS 12 level. Note that if the PVL1 pump is started at a low speed of 950 r / min, the maximum fluid viscosity is limited to The maximum permissible deviation is less than 0.1 mm (.004 in.) TIR and maximum allowable error Less than 0.2 °. CIT-03-04-50，YUKEN葉片泵參數

CIT-03-04-50，YUKEN葉片泵參數的詳細介紹

    CIT-03-04-50，YUKEN葉片泵參數
    企業QQ：2880626087
    電話；021-69001039
    手機；17321017802（微信）
    郵箱；17321017802@163.com
    聯系人；周彩云
    地址：上海市嘉定區江橋嘉涌路99弄6號713室
    1. Type of hydraulic oil
    Oil base oil ........... U. Se R & O (rust and oxidation inhibitor) type oil or anti-wear type oil.
    In addition, use a 100 mm (150 mesh) fuel tank filter on the suction
    side and install a tank with a distance of more than 50 mm (2 inches).
    200mm 2 / s (910SSU).
    Description
    3. Pollution control
    (Equivalent to ISO VG-32 or 46)
    Note: Only oil base oil can be used for hydraulic oil.
    2. Recommended viscosity and oil temperature
    The viscosity range is 20-400 mm 2 / s (100-1800 SSU).
    , Directory number. EC-3001), or air is discharged by a slightly loose discharge side connection.
    When starting, run the pump as intermittently as possible without load.
    Use hydraulic oil that meets the recommended viscosity and oil temperature.
    Refer to the "Hydraulic Oil" section above for fluid viscosity at start-up.
    4. Other precautions
    If you are using a PVL1 series single pump at speeds below 1200 r / min,
    install the pump above the suction port
    Use a flexible coupling as much as possible and avoid any stress generated by bending or thrust.
    Hydraulic fluid contamination leads to pump failure and reduced pump life. adequate
    Axis alignment
    CIT-03-04-50，YUKEN葉片泵參數
    If the pump is installed on top
    The tank level is set below the oil level below 1.0 m (3.3 ft.).
    Oil temperature at 0 / + 70 ° C (32 - 158 ° F)
    So that the pump is easy to draw fluid at start-up.
    3. Start the note
    The pump may be difficult to draw fluid during initial operation or for a long period of rest.
    In this case, the exhaust valve should be pre-installed on the discharge side (model number ST1004 - - 10)
    2. Inhalation pressure
    The suction pressure is set at -20 to +30 kPa (5.9 in.Hg to +4.3 PSIG) at the pump inlet.
    In addition, use the suction pipe of the size shown in the dimension drawing.
    CIT-03-04-50，YUKEN葉片泵參數
產品留言
標題
聯系人
聯系電話
內容
驗證碼
點擊換一張
注：1.可以使用快捷鍵Alt+S或Ctrl+Enter發送信息!
2.如有必要,請您留下您的詳細聯系方式!



名稱：上海乾拓貿易有限公司
上海地址：上海市嘉定區嘉涌路99弄6號713室

聯系人：羅丹
QQ：2880626082
直線電話：021-39526590
聯系人： 18917038407（同微信）
郵箱：18917038407@163.com


聯系人;沈雪
企業QQ:2880626081
手機；18918574312（微信） 
電話；021-69000975
郵箱:18918574312@163.com


聯系人：章瑩玲
企業QQ:2880626085
手機；18918572467（微信） 
電話；021-69000973
郵箱:18918572467@163.com


聯系人：王亞波
QQ:2880626088
021-39529839-8012
手機：17321056802（同微信）
郵箱:17321056802@163.com


上海乾拓貿易有限公司    地址：上海嘉定嘉涌路99弄6號713    郵編：
聯系人：單先生    電話：021-69000975   手機號碼：18918574312    傳真：021-39947181
滬ICP備09006758號-2  
 

滬公網安備 31011402005013號
點擊這里給我發消息 點擊這里給我發消息 點擊這里給我發消息 點擊這里給我發消息 點擊這里給我發消息 點擊這里給我發消息 點擊這里給我發消息