AL40-N04+Y400T，日本SMC油霧器[產品打印頁面]

AL40-N04+Y400T，日本SMC油霧器

僅通過調整差壓就可輕松實現給油量設定。
通過開關給油塞可在不停止通氣的情況下實現補油。
可通過給油孔觀察到微霧的產生情況。
Symbol: A43 Applicable to single vane type only
A special end is machined onto both the long and short shafts, and a through-hole is
drilled into both shafts. Female threads are machined into the through holes, whose
diameter is equivalent to the diameter of the pilot holes.
• The maximum dimension L1 is, as a rule, twice the thread size.
• Applicable shaft types: K, T • Equal dimensions are indicated by the same marker.

Symbol: A44 Applicable to single vane type only
可通過升壓器提供高于主空氣通路的壓力，
這個壓差可以看做是油霧產生的壓差，因此主空氣通路的壓力下降很少。
僅通過調整油霧產生的壓差達到微霧恒定供給。
通過開關給油槽可在不停止通氣的情況下實現補油。
可通過給油孔觀察到微霧的產生情況。
A special end is machined onto both the long and short shafts, and a through-hole is
drilled into both shafts. Female threads are machined into the through-holes, whose
diameter is equivalent to the diameter of the pilot holes

• The maximum dimension L1 is, as a rule, twice the thread size.
• Applicable shaft types: J, X, Z • Equal dimensions are indicated by the same marker.
Symbol: A39 Applicable to single vane type only
?Minimum machining diameter for d1 is 0.1.
?Applicable shaft types: S, Y
從油箱和噴霧器的開關控制部分將油和空氣傳送到混合閥。
LMV  混合閥 因內置有油針閥和空氣針閥，
在油霧噴射單元對油量和空氣量進行調整
，然后同時由噴嘴噴出。
LMH  磁石保持座 支架前端裝有混合閥，

可自由安裝在機床等機械的鋼鐵部分。
LMD  分支管 在使用多個混合閥的場合，
用于將來自油霧噴射單元的油和氣體分開。
Symbol: A41 Applicable to single vane type only
?Minimum machining diameter for d1 is 0.1.
?Applicable shaft types: J, X, Z
Symbol: A40 Applicable to single vane type only
Shaft with through-hole
?Minimum machining diameter for d1 is 0.1.
列/CAD 接管口徑 1次給油量 (cm3)

ALIP  壓力型 1/8 0～0.04
ALT10  油箱 氣：1/8
油：1/4 油箱容量： 160cm3
ALT20  油箱容量：1000cm3
特長 在潤滑點之前直接供給一定量的油。
能夠為潤滑油不容易到達的回路或空氣消耗量小的場合提供可靠的定量供油。
?Applicable shaft types: K, T
Symbol: A42 Applicable to single vane type only

A special end is machined onto both the long and short shafts, and a through-hole is
drilled into both shafts. Female threads are machined into the through-holes, whose
diameter is equivalent to the diameter of the pilot holes.
?The maximum dimension L1 is, as a rule, twice the thread size.
?Applicable shaft types: S, Y ?Equal dimensions are indicated by the same marker.


 

產品留言

標題

聯系人

聯系電話

內容

驗證碼

點擊換一張

注：1.可以使用快捷鍵Alt+S或Ctrl+Enter發送信息!
2.如有必要,請您留下您的詳細聯系方式!