SMC針形氣缸，CDJP2B6-10D-97
電話：O21-3952 9829/3O-8O1O
傳真：O21-6O83 1959
手機：189 1857 2467
Q：125 5O9 6653
聯系人：張海情
郵箱：8010@shqiantuo.com.cn
針形氣缸 CJP2/CDJP2/CJP
形式 系列/CAD 動作方式 缸徑 (mm)
標準型 CJP2 單杠雙作用 4, 6, 10, 16
標準型 CJPB 單作用(面板安裝) 4, 6, 10, 15
標準型 CJPS 單作用(埋入式) 4, 6, 10, 15
特長 缸徑φ4-5st也可安裝2個磁性開關。
能連接φ2快換接頭、速度控制閥。
帶磁性開關(CDJP2系列：CDJP2)
慎重
驅動的慣性負載時，操作動能在允許值內的筒狀體。在下面的圖表是由粗實線劃定的范圍表示負載質量和行駛速度之間的關系。
容許橫向負載
嚴格觀察活塞桿上的橫向載荷的限制范圍。 （請參閱下面的圖。）如果這個產品是用來超越的限制，可能會縮短機器使用壽命或造成??損壞。
1。適合自動切換到自動開關安裝槽，設置自動切換到安裝位置的大致。 w后再次確認檢測位置，自動開關安裝螺絲擰緊。以固定自動開關。
2。應的檢測位置的變形例中的條件的q..自動開關安裝螺釘擰緊時一個鐘表匠crewdriver的，可以使用帶手柄ofapproximately5至6毫米直徑（約0.10?0.20 N·M的扭矩?cái)Q緊。）
慎重
安裝螺母的擰緊力矩和面板寬度
1。缸或支架安裝時，不要施加更大的扭矩比扭矩范圍。另外，不要附加面板厚度超出指定的范圍。
2.Do不適桿端關節軸承，桿端帽，單或雙指關節上的負載連接時的擰緊力矩比低于規定范圍。
SMC針形氣缸，CDJP2B6-10D-97
Caution
When driving an inertial load, operate a cylinder with kinetic energy within the allowable value. The range in the chart below that is delineated by bold solid lines indicates the relation between load mass and maximum driving speeds.
Allowable Lateral Load
Strictly observe the limiting range of lateral load on a piston rod. (Refer to the below graph.) If this product is used beyond the limits, it may shorten the machine life or cause damage.
1. Fit an auto switch into the auto switch mounting groove to set it roughly to the mounting position for an auto switch. w After reconfirming the detecting position, tighten the auto switch mounting screw. to secure the auto switch.
2. Modification of the detecting position should be made in the condition of q.. When tightening an auto switch mounting screw, use a watchmaker’s crewdriver with a handle ofapproximately 5 to 6 mm in diameter.(Use a tightening torque of approximately 0.10 to 0.20 N·m.)
Caution
Mounting nut maximum tightening torque and panel width
1. Do not apply more torque than the maximum torque range when mounting the cylinder or bracket. Also, do not attach a panel with a thickness beyond the specified range.
2.Do not apply more tightening torque than the below specified range when attaching a load on the rod end, rod end cap, single or double knuckle joint.
SMC針形氣缸，CDJP2B6-10D-97
